Hot Products
0102030405
China Precision T-Nuts: High-Quality Fastening Solutions from Leading Suppliers & Factory
Product Introduction Introduction
A T-shaped nut is a component that uses a nut to tighten together with a bolt or screw. Depending on its use in manufacturing machinery, the same component can be divided into several categories based on its material, including carbon steel, stainless steel, non-ferrous metals, etc. A T-shaped nut is a type of nut that looks like a T. T-nuts are not only easy to install and unload, but also easy to install parts in any position, which can greatly improve labor productivity. This is also why T-nuts can be widely used in T-grooves of various milling machines.
Usage products
How to use the T-nut:
- 1 The T-nut and hexagon bolts are installed on the corner pieces without tightening.
- 2 The T-nut is stuck in the groove along the notch of the aluminum profile and installed with a shrapnel flat gasket.
- 3 It is good to tighten it with a screwdriver.
| Thread size | M4 | M5 | M6 | M8 | M10 | M12 | M16 | M20 | M24 | M30 | M36 | M42 | M48 |
| Pitch | 0.7 | 0.8 | 1 | 1.25 | 1.5 | 1.75 | 2 | 2.5 | 3 | 3.5 | 4 | 4.5 | 5 |
| Nominal | 5 | 6 | 8 | 10 | 12 | 14 | 18 | 22 | 28 | 36 | 42 | 48 | 54 |
| maximum | 4.7 | 5.7 | 7.7 | 9.7 | 11.7 | 13.7 | 17.7 | 21.7 | 27.7 | 35.6 | 41.6 | 47.6 | 53.6 |
| minimum | 4.5 | 5.5 | 7.5 | 9.5 | 11.4 | 13.4 | 17.4 | 21.4 | 27.4 | 35.3 | 41.3 | 47.3 | 53.2 |
| maximum | 9 | 10 | 13 | 15 | 18 | 22 | 28 | 34 | 43 | 53 | 64 | 75 | 85 |
| minimum | 8.5 | 9.5 | 12.5 | 14.5 | 17.5 | 21.5 | 27.5 | 33.5 | 42 | 52 | 63 | 74 | 84 |
| maximum | 2.5 | 4 | 6 | 6 | 7 | 8 | 10 | 14 | 18 | 23 | 28 | 32 | 36 |
| minimum | 2.2 | 3.5 | 5.5 | 5.5 | 6.5 | 7.5 | 9.5 | 13.5 | 17 | 22 | 27 | 31 | 35 |
| 6.5 | 8 | 10 | 12 | 14 | 16 | 20 | 28 | 36 | 44 | 52 | 60 | 70 |
During the use of T-nuts, special attention should be paid to the following aspects:
1. Specification matching
Ensure that the specifications of the T-nut (such as thread size, T-groove width, etc.) are fully matched with the requirements of the bolt, T-groove, and application scenario to ensure the tightening effect and stability.
2. Material selection
Choose the appropriate material for the T-nut based on the environmental conditions of use, such as humidity, temperature, corrosiveness, etc. For example, in humid or corrosive environments, stainless steel nuts should be preferred to prevent rust and corrosion.
3. Installation direction
Install the T-shaped nut correctly so that it can slide smoothly in the T-shaped groove and reach the expected fastening position.
4. Pre tightening force control
When tightening, pay attention to controlling the size of the pre tightening force. Insufficient pre tightening force may result in an unstable connection, while excessive pre tightening force may damage nuts, bolts, or connected components.
5. Surface cleaning
Before installation, ensure that the surface of the T-nut, T-groove, and mating components is clean, free of debris, oil stains, and rust, to ensure good contact and fastening effect.
6. Inspection and maintenance
Regularly check the tightening status of the T-nut, and if it is loose, it should be re tightened in a timely manner. At the same time, check whether the nut is worn, deformed, or damaged, and replace it promptly if necessary.
7. Load limit
Understand the load-bearing capacity of T-nuts and avoid using them beyond their rated load to prevent failure.
8. Installation tools
Use appropriate tools for installation and disassembly to avoid damage to nuts or connectors caused by improper tools.
In short, when using T-nuts, various factors should be comprehensively considered and strictly operated according to specifications to ensure their performance and safety.
Company Introduction company
The company's products are widely used in various fields such as wind turbines, shield tunneling machines, tower cranes, petrochemicals, marine engineering, automobiles, nuclear power, rail transit, and high-end mechanical equipment, and can adapt to various requirements such as high temperature resistance, low temperature resistance, and corrosion resistance. The product is exported to various parts of the world and has received unanimous praise.
Frequently Asked Questions FAQ
What materials are T-shaped nuts made of?
T-shaped nuts can be divided into several categories based on materials, including carbon steel, stainless steel, and non-ferrous metals, depending on their specific industrial application.
Why are T-nuts widely used in milling machines?
T-nuts are easy to install and unload, and they allow parts to be positioned anywhere along the T-groove, which greatly improves labor productivity in milling machine setups.
How do you install a T-nut correctly?
First, loosely install the T-nut and hexagon bolts onto the corner pieces. Then, slide the T-nut into the aluminum profile groove along the notch and fit it with a shrapnel flat gasket. Finally, tighten the assembly securely using a screwdriver.
What material should be chosen for humid or corrosive environments?
In humid or corrosive environments, stainless steel T-nuts should be preferred to prevent rust, corrosion, and structural degradation.
In which industries are your products applied?
Our products are widely applied in wind turbines, shield tunneling machines, tower cranes, petrochemicals, marine engineering, automobiles, nuclear power, rail transit, and high-end mechanical equipment.